Simple Wristband Attachment AccessoryBlind

in 3D Printing Design held by dbraun22
Contest Ended, Winner(s) have been selected.
  • Open
  • Choosing Finalist
  • Ended
Description:
This contest is to design a very simple wristband attachment accessory piece that can hold a piece of fabric that was cut in a circle. The overall shape of the piece is a football/oval shape. I am attaching some pictures to show a prototype that I made out of paper. There should be 2 triangle shaped holes on the 2 ends that I can attach the piece to. There should also be an inner circle where I can glue the circle cut of fabric. The inner circle should be indented about a millimeter inward from the flat surface to place the cut of fabric. The inner circle should also be 1/2 inches in diameter. There should also be an outline around that inner circle that is flat with the front surface and that outline circle should be a diameter that is about 6 millimeters wider than the inner circle. The overall piece should be about 1.25-1.5 inches long in width from end to end and about 5/8 inches in height from the tallest point in the middle of the piece. All of these measurement can be changed if needed to make the design better, but the inner piece that fits that fabric should be able to comfortably fit a piece of fabric that is 1/2 inches in diameter.
Wants:
I want the piece to be able to be 3D printed in white. The dimensions should be as described in the description: 1.25-1.5 inches long, 5/8 inches high, and with the cuts and indentations that I described and are similar to the images for this contest posting. The overall piece should also be kept fairly thin because it is worn on a person's wrist.

Entries

= Buyer's Rating
1st Winner
#16 #1 by DesignAssist
#10 Version2 by Mike Mansour
#4 Simple Wristband Attachment Accessory by Mikhail Shcherbakov
#19 Simple Wristband Attachment Accessory by yuvaraj l
#11 G:\CADCrowd by PaRtH KuMaR
#28 Simple Wristband Attachment Accessory by yuvaraj l
#29 Wrist Band Accessory by CBee18
#30 Simple Wristband Attachment Accessory by sherifelsheikh
#31 Wristband Design 1 by Oscar47z
#32 Wrist band attachment_1 by Aditya0193
#33 Simple Wristband Attachment Accessory by Bijay Ghimire
#34 Simple Wristband Attachment Accessory 2 by Bijay Ghimire
#35 Simple Wristband Attachment Accessory by yuvaraj l
#36 Wristband Attachment Accessory by Henry Prince
#37 Simple Wristband Attachment Accessory by sherifelsheikh
#38 Wristband by Fadi Sayegh
#39 Wristband by Fadi Sayegh
#42 Wristband Accessory by BranTheCADMan
#14 Simple Wristband Attachment Accessory by Sameer Gupta
Download Files
#2 Simple Wristband Attachment Accessory by RRM
#7 Simple Wristband Attachment Accessory by edward m barnes
#8 Simple Wristband Attachment Accessory by edward m barnes
#9 Version 1 by Mike Mansour
#12 Updated "Wristband Design" by PaRtH KuMaR
#25 Wristband attachment_02 by Oddie Salazar
#15 Simple Wristband Attachment Accessory by Sameer Gupta
#18 Simple Wristband Attachment Accessory by yuvaraj l
#21 Simple Wristband Attachment Accessory by sherifelsheikh
#1 Simple Wristband Attachment Accessory by sherifelsheikh
#23 Wristband attachment by Oddie Salazar
#24 Wristband attachment_01 by Oddie Salazar

Discussion

Thu, 30 Aug 2018 11:30:33 +0000
YES, NOT ABLE TO OPEN THE ATTACHMENT.
Wed, 29 Aug 2018 06:41:55 +0000
Please make the contest prepaid
Wed, 29 Aug 2018 04:00:19 +0000
Just rename the attachment file to *.jpg

PaRtH KuMaR

Designer

Tue, 28 Aug 2018 20:33:23 +0000
Got opend

PaRtH KuMaR

Designer

Tue, 28 Aug 2018 20:25:39 +0000
Could you please provide the attachment file type. I couldn&;t able to open it

Similar Contests on Cad Crowd

pocket box 2
Place lid on container via living hendge< so it can open up clam style
Sketch drawing to CAD/.stl file
Need the sketch/measurements of each unit converted into a CAD drawing so we can have a 3D prototype printed.
Logo and stationary design
Hi, Freelancer, i need help from graphic designer, Just iam starting New business, i would like to have Logo and all required stationaries (Logo Design, Power point presentation them and Visiting Card Design and Letter HEAD Design.) Please note following information will help you for your contest 1-Company product is - Engineering service provider in Mechanical/Architect/IT/Graphic design, present website is www.sonenengineering.com this is old site and not covering all versicle, (Present website is not good after these design i want develop website design, i may required your help for rendering of images, page design etc.) 2-You can think 3d logo, you can think symbol with globe, you can think combination of both, iam open to all ideas not specific. 3-Sonen mean is sunrise 4-I prefer descent corporate logo, i do not like too dark, too crowded. 6-For power point presentation theme i have attached one example what i mean. 7-For Visiting card i will provide contact details at final stage. 8-letter head also required descent. Deliverable : All source files and and onset pdf, Jpg. company name is sonen engineering solutions iam expecting something different from regular so that will help me to take ealy decision, presently all looks similar concept.
3D Printing Design | Meet the minimum thinkness on two small parts of my 3D STL file for Shapeways!
I need someone to make a certain part of my 3D anchor stl file a little thicker. Nothing complicated at all! The guy that was working on this file is really swamped with work and cannot complete this edit. This job should literally take less than 30 minutes if you know what you are doing. On the attached picture it shows that I need to make specific parts of the anchor a little thicker to meet the minimum supported wire thickness of .8mm. Here's what the email I recieved from shapeways said: "Here is why we cannot print your model: The minimum thickness for free/supporting wires > 1.0mm and supported wires > 0.8mm for this material. Please thicken the wires of the model." I have specified what needs to be done on the picture attached. Please message me if you need clarification. If you know what you are doing and have worked with stl. files and understand the thickness minimum that shapeways requires for 3d printing then this should be a no-brainer.
Ring design with branches and bramble
We are looking for a ring that will eventually be printed in sterling, featuring bare branches. Ring band needs to resemble a branch (or branches), and the top of the ring needs branches wrapping about it. Inside this ring we'll be adding an element later, so we need a pocket underneath the branches that will fit an item that is approx 5mmx20mm. The design sketch shows a bit of a lip to the pocket from the side view, this will help keep the item in place. Once the design is approved, we'll need it in US sizes 5-13.