Lawn Edge BarrierBlind

in 3D Modeling Design held by marcp1
Contest Ended, Winner(s) have been selected.
  • Open
  • Choosing Finalist
  • Ended
Description:
The attached image "Installed prototype Attachment #1" is the current design of our patent pending lawn edger. It prevents the grass and weeds from growing over the edge of the hard surface.

We have been asked by the client to:
1. Make the current prototype longer
2. Make it flexible so that it will bend around soft curves and 90-degree corners when installed as well as for packaging purposes (see Attachment #2).
3, Product design length shall be customizable by cutting or other methods of users' desired length.
4. The desired cost should be under $25
Wants:
Note: Using the attached file CAD Lawn Edge Design-12" (Attachment #4)

1. Lengthen the entire device from 96" to 240" (preferred length is 240 inches)
a.) Vertical below and above surface barrier component Dimensions (LxWxH) are 96x 0.88 x 6 inches or 2,438.4X 22.352 x 152.4 mm
b.) The horizontal surface barrier must be flexible to bend/expandable to cover corners and curves Dimensions (LxWxH) are 96 x .1875 x 1.25 inches or 2,438.4 x 4.7625 x 31.75 mm

2. Redesign the lawn edger to make it flexible so that it can bend around curves, and corners, with a minimum of 90 and up to a 180-degree angle. Keep in mind that the product will be rolled for packaging/retail. See Attachment #3 for reference of similar products packaged.

(Note: Contestant can submit a draft for review and feedback )
Don't Wants:
1. New CAD designs in solid works

2. A 3D animated video, demonstrating how it is unwrapped from the packaging (like Attachment #3), installed in the grass, and bends around curves and hard corners in both directions.
Software:
  1. SolidWorks
Additional Information
What I Don't Want:
- Product design that does not use standard manufacturing equipment and tooling.
- Product that does not meet the evaluation criteria provided above.

Want :
1. New CAD designs in solid works
2. A 3D animated video demonstrating how it is unwrapped from the packaging (like Attachment #3), installed in the grass, and bends around curves and hard corners in both directions.

(Revision to Description)

Entries

= Buyer's Rating
#3 Washing machine top frame by sanjeewae
#4 Washing machine top frame by sanjeewae
#8 Lawn Edger R0 by Indranil_Routh
#9 bendable lawn edge barrier concept by RBLdesign

Discussion

abhi007

Designer

Wed, 23 Nov 2022 04:39:31 +0000
Yes, 4 hours would be sufficient. Thanks.

marcp1

Buyer

Mon, 21 Nov 2022 22:06:41 +0000
I will see if it can be set for 4 hrs. Will that be enough time? You will need to watch for it to be reopened.

marcp1

Buyer

Mon, 21 Nov 2022 22:06:40 +0000
I will see if it can be set for 4 hrs. Will that be enough time? You will need to watch for it to be reopened.

abhi007

Designer

Sun, 20 Nov 2022 10:37:47 +0000
Hello @marcp1, I request you to open the contest for few hours. I was done with the modifications and ready to upload the design. But the contest ended.

Inerapello

Designer

Wed, 09 Nov 2022 00:30:56 +0000
Hi Marc! Kindly rate the Design Submissions so we can know if you like our Design.
Mon, 07 Nov 2022 19:33:42 +0000
Hi, Can you resend the file "Modified drawings 1" in step format?

marcp1

Buyer

Sat, 05 Nov 2022 17:16:39 +0000
Thank you all for participating and asking questions for clarification. I’m looking forward to seeing the creative ideas that will be submitted.

Please see the response to the questions provided:
1.) Do you have a particular material in mind that the edger should be made from?
(Ans) No, there’s no particular material required. The current material submitted but not final is polyurethane. We are looking for the best material and solution to meet customer&;s requirements.

2.) What is the minimum radius you want for going round bends?
(Ans) The center Please see the attached sketch. Let me know if it doesn’t answer your questions.

3.) Attachment is not a CAD file as you have stated. It is only a PDF. So, I am confused as to what it is you want. Just change the drawing or do you want a CAD model and a new drawing? You are also VERY specific about what you DO NOT want in a video. That seems odd. Can you verify that you DO NOT WANT a new design OR a video.?

(Ans) My apology for the confusion.
(a) The final drawing will need to be in CAD model (for designers and engineers) but we will also need a pdf (management).
(b) Please proceed with providing new CAD drawings. However, will also submit current CAD drawings just in case that helps.
(c) The current design was provided as a reference for making changes or adding to accomplish the goal, which is flexibility (see attached) and extended length (3 -20 ft). There are key components to use in your new or revised design. The first is a surface barrier that sits on the hard surface (cerement, pavement, asphalt, etc.); and the second is the vertical barrier that goes into the ground. Together the current design eliminates the need to edge and prevents overgrowth on the surface.
How the designer chooses to design and the type of material used to design is up to the contestant.
(d) Shall we alter the dimensions as per our design modifications? Yes, the dimensions can be altered. The main requirement per customer is to extend the length from 1 ft. to 20 ft, with 3 ft being the minimum.
4.) Shall we alter the dimensions as per our design modifications?
Ans) The dimensions can be altered to meet requirements. However, the requested length is 3ft to 20f.
Problem: The current design prevents grass from growing on the hard surface. It has a low profile so it won’t interfere with the lawn mower (see video). However, the customer needs this design to be 20ft (min. 3ft) and flexible to bend around curves/corners. This is difficult with a plastic surface barrier (horizontal part) won’t allow flexible bends.

Inerapello

Designer

Sat, 05 Nov 2022 13:54:04 +0000
Hi! Shall we alter the dimensions as per our design modifications?
Fri, 04 Nov 2022 23:48:53 +0000
attachment is not a CAD file as you have stated. It is only a PDF. So i am confused as to what it is you want. Just change the drawing or do you want a CAD model and new drawing? You are also VERY specific about what you DO NOT want in a video. That seems odd. Can you verify that you DO NOT WANT a new design OR a video.
Fri, 04 Nov 2022 18:59:26 +0000
Hi. An interesting design.
I have two questions
1. Do you have a particular material in mind that the edger should be made from?
2. What is the minimum radius you want for going round bends?

Thanks

Rob

Similar Contests on Cad Crowd

Home Automation casing
We are looking for sleek or a very sexy casing for Home automation device that can add beauty to your house along with making your day to day life easy. We want out of the box thinking, not just any enclosure. The logo will be Maestro, the designer can create it with no limitation for your imaginations. Attached is a pdf file with full requirements and description.
cartridge belt
Greenearth's cartridge belt contains 13 rubber squeeze bulbs containing 2.3 ml of fluids. The belt measures 4 cm wide and 1.5 cm high. The length is determined in the final stages. The materials requirements are for retractable rubber silicon for the mounted squeeze bulbs & clear in color. The belt is the base and must be of thicker silicon it is shaped with cones to stabilize the bulbs as they rotate round plus a retrieval tag at each end of belt. Drawing will follow, 20days
Can crusher design ( will pay)
Hello I am a student in need of serious help with a can crusher design will pay and need it done right away
Brush Cleaner
I would like a electric brush cleaner which has a base that fits into the palm of your hand and multiple detachable head pieces. Must be either rechargeable or battery operated. Base: - approx. 3 inches in width - has mechanics to rotate head piece both ways - possible liquid containing compartment that can dispense foam cleanser through head piece - strap that secures base to palm of hand Head: - approx. 3inches in width - Flat top with a short lip to retain liquid - Should have various sized bumps to help with cleansing brush head - can attach securely to base Similar construction to a clarisonic skin cleaner, but without the handle. Please see attached images
Spider Clip - NO Drop Cell Phone Holder
A retractable tether from a belt clip that easily attaches to the back of any cell phone. - Tether should be 42" long. - Tether housing clips to belt. - Opposite end of tether attaches to back of cell phone by either strong suction cup or strong Velcro with plastic teeth to handle repeated detaching and attaching. - Tether needs to be able to lock in position at any length like a tape measure. - Tether housing should have 3 different mini clips on it. One on the lower face so the back of the cell phone attachment can hook to the tether housing. One on each side or the tether housing for hanging a key or a bluetooth devise. Take the basic key back or badge holder