Show me the Light - Crowd test for photometrics freelancer
in
Architectural Design
held by
AutoLume
Last seen:
Contest Closed
-
Open
-
Choosing Finalist
-
Ended
Description:
Need photometrics for interior and exterior of car dealership. Needs to be able to tell us what light levels is best and what product (LED only) you recommend for the entire dealership.
Wants:
Knowledge of automotive dealership lighting, CREe, GE and other LED luminaries as well as attention to detail on each photo metric layout
Don't Wants:
poorly experienced people providing their work.
Ask for Sample:
please send a dealership sample using CREE products
Software:
- your choice
Entries
No Entries Submitted Yet.
Discussion
It´s very important to have a layout with general dimensions of the car dealership. For example in the interior you have a "exhibition area" and a "Service and repair area" this last one is very important because for example GM has some regulations with the light you must use.
Fri, 26 Jul 2013 19:59:58 +0000
Need a drawing or an address, input power spec would be nice as well.
Fri, 26 Jul 2013 14:00:02 +0000
Does the customer have any site plans? DWG would be best. Otherwise an address might work.
Similar Contests on Cad Crowd
Residential house
Hello I have a floor plan for a house in new Zealand that i need some concepts drawn up for the elevations and roof design in dwg format. I am open to Ideas that any architects have to add to the design. option of modern or traditional design would be great,
feel free to alter the floor plan attached to make your desing work but still keep the same basic layout concept.
a few guide lines:
2.4m Ceiling height
concrete floor
timber frameing construction
mix of brick veneer and rendered cladding
floor to ceiling sliding door in the kitchen lounge/family room
must have and soffit overhang.
thanks and have fun.
Create Professional Title Page for Building Envelope Company - AutoCAD or Chief Architect
We want a freelance designer to create a professional title page for our company. Our old title page doesn't look very good; please refer to "Peerless Old Title Page.pdf" file (please ignore drawing details). See this screencast for notes: http://bit.ly/Y7Ntwa
We need the drawings produced (in imperial/metric) with these dimensions:
8"x11" (also need in metric)
11"x17" (also need in metric)
36"x24" (also need in metric)
Our logo should be included on the title block. Please see the file attachments for work details and let us if you have any questions. There is a lot more upcoming work that we may ask the best contrator to help out with in the near future.
Note: Ideally, the CAD software should be Chief Architect or in an AutoCAD format that can be imported into our software.
Gallery Construction calculations
This task requires calculating which profiles to use for a gallery structure!
No need to design or draw anything in this task. Only calculate.
The attached plan was made by an engineer for building a gallery in my house from steel profiles but I suspect the profiles he chose are an over kill so I'd like to hear some more opinions. I assure everyone I will ultimately build the gallery under his approval.
The 40 square meters gallery is to be used for 2 living rooms for my kids. It will hold normal furniture that such rooms should hold.
The main beam would be HEA, IPN or another profile you may recommend for decreasing the profile height.
The main beam would be made of 2 parts welded together and an RHS or IPN pillar underneath the connection point. I am not sure yet where the pillar would be, therefore I need the main beam profile calculated for 2 options: 390cm + 600cm or 270cm + 720cm.
Each part of the main beam might be a different profile so please calculate the minimal required profile for each part.
I would also like to know what profile measures I would need if there was to be no pillar in the middle of the main beam and it would be a one piece of 990cm.
All other 3 sides of the gallery have an existing wall and part of this wall has an existing reinforced concrete belt (yellow in the drawing). There are also 4 existing reinforced concrete pillars as appears in the drawing.
It is planned to have a UPN profile (welded together as one) all along the 3 other sides.
The whole structure will be supported by 6 RHS pillars (the main beam middle pillar might be IPN) that will be attached with Jumbo screws and chemical adhesive to reinforced concrete floor.
At the back plane of the gallery the 3 RHS pillars are very close to existing reinforced concrete pillars. Is it possible to attach the UPN to the existing pillars and make do without these 3 RHS pillars?
The main beam and the back plane will be connected with 15 IPN beams.
I still don't know if the length of these beams will be 429cm or 470cm so I need both options calculated.
The floor surface will be made of several layers for isolation with 30mm pine wood at the top.
I need to know what are the minimal measures for all the profiles in my plan and according to which assumptions the calculation was done.
One last question. Above the gallery there is a 10meters wide by 8 meters long wooden shingle roof (as in the photos) that is supported by small wooden pillar in the middle. I need to install a 10meter steel beam from side to side at the middle of the roof so that I can remove the supporting wooden pillars. What would be the minimal IPN profile to use for that? Would IPN 100 or 120 do the job?
Calculate the following profiles:
Main IPN or HEA beam at 720cm + 270cm (2 different profiles?):
Main IPN or HEA beam at 600cm + 390cm (2 different profiles?):
UPN:
Width IPN beams at 429cm:
Width IPN beams at 470cm:
RHS pillars:
IPN pillar:
Roof 990cm IPN beam:
Any improvement suggestions are welcome.
Assisted Living Floor Plan Animation
I have a floor plan for an Assisted Living Facility that is currently under construction. I need a floor plan animation for the purpose of marketing materials etc. Posted is a picture of two colored layouts of our individual apartments. I posted also a black and white picture of the building's layout. I would like to have the black and white layout re-made to match the colored layouts. For the building layout, it is not necessary to include details like the showers, toilets, sinks, furniture etc. Sketchup was used to build the room layouts, it is suggested to use sketchup to match them.
Floor Plan for a Home Remodel
Draft up a floor plan for a phase 1 & phase 2 of my home remodels. I have chief architect and can do some basic designs. Looking for some creative layout ideas with the space I have now (phase 1) then the added space that phase 2 will add. I'm stumped on how to layout the interior walls the best way.
CyP Solution