quadcopter UAV design contest

in Product Design held by venkata srinath
Contest Closed
  • Open
  • Choosing Finalist
  • Ended
Description:
I need a unique, rugged quadcopter UAV design,analysis and all necessary fabrication details for production in large quantities.The quadcopter should have a high endurance similar to the Microdrones Md4-1000
LINK:
(www.microdrones.com/products/md4-1000/md4-1000-key-information.php

The quadcopter should be modular in nature like the Aeryon Scout
LINK:
Scout(ww1.prweb.com/prfiles/2010/09/01/3259734/MG1969.JPG)

NEEDS:
good aesthetic design,analysis along with all production details,
modular nature,
Materials used,
Sourcing details,
Bill of materials(BOM)
Wants:
Please clearly specify ALL design,analysis,fabrication details that are absolutely essential for production in large quantities.I should be able to enter production stage using the inputs given.Materials should be easily available for production of the product.
LOOKING FOR A COMPLETE SOLUTION FROM PRODUCT DESIGN TO FABRICATION.
Software:
  1. SolidWorks

Entries

= Buyer's Rating
#2 Quadcopter by Shad ahmad
#1 1 by rif

Discussion

Mon, 19 Aug 2013 06:33:12 +0000
are you just using solidwork ??, i can&;t use solidwork..
can i using autodesk Inventor to make all of it ??
Tue, 23 Jul 2013 19:40:21 +0000
$160 are you missing some zeros? Missing a lot of details in your project description. I have scratch built multiple quad&;s and couldn&;t even start analyst for $160.
Tue, 23 Jul 2013 04:40:55 +0000
i will definitely extend my budget ..no issues on that...looking for a good response..thank you.
Tue, 23 Jul 2013 00:40:49 +0000
The weight of all the internal components from what should be deducted? From components that we like the most? And for 160$ including the all analysis? O_O
Mon, 22 Jul 2013 19:35:45 +0000
I think he left out a zero.

Similar Contests on Cad Crowd

Design a next generation, WiFi controlled sprinkler unit
We are building a WiFi enabled irrigation unit and need a prototype 3D design that we will print. Here is our company www.h2lo.co I have included these photos just to show what the slot on the bottom will look like for the consumer to attach wires to the sprinkler relay. http://rayshobby.net/wordpress/wp-content/uploads/2013/03/IMG_2424-300x200.jpg http://rayshobby.net/wordpress/wp-content/uploads/2013/03/IMG_2425-300x200.jpg http://rayshobby.net/wordpress/wp-content/uploads/2013/03/IMG_2426-300x200.jpg This design will encase a PCB board with a relay.
Control-box with display, fitting on a DIN rail
This is about a first product draft, which shall later be turned into a production ready design. I need an enclosure for a custom made electronic part. The rough form-factor should be similar to a navigation system (see attached files) with a display in front and parallel enclosure boundaries, slightly rounded edges. The display is 4.3 inches wide (see technical details attached) and should be included in the rendering. The enclosure should be 4 cm deep. As a bonus, the display shows attached bar diagram. At the back, there should be the possibility for a DIN rail mount, top hat rail EN 50022 – 35 × 7.5 but also for direct wall mount using screws or mounting to a bar with cable ties. At the front left side of the enclosure, I need a C14 inlet to add a power cable and a Schuko socket: https://en.wikipedia.org/wiki/Schuko or CEE 7/3 socket. See attached figure of the design. The material should be dark grey with a bit reflective surface. Please add our logo to the upper left corner of the front, below the display. If it fits optically, it could glow a bit in green.
Need 3D Design and CAD for Toy Helicopter - New Product Prototype
We are a manufacturer of Remote Control Toys. We are looking to design a line of flying animals using the base of a current helicopter (attached are pics). We will need the designer to design the outside body in the shape of a Pig, Making a remote control flying pig. The landing gears can be taken off, and the pig will encompass the whole helicopter body. Please submit design 3D design work for a flying Pig.
Electrical roller door
Design an electrical roller door using neoprene or similar material for door. Roller at top.
4-to-Score Giant
We are an e-commerce company selling on Amazon, eBay, Walmart and our e-commerce website. Our target audience is Children. We want to design a 4-to-Score Giant like this url https://www.amazon.com/s?k=4-to-Score+Giant&ref=nb_sb_noss. And now we don't have any good idea yet.