Need 3D Design and CAD for Toy Helicopter - New Product Prototype
in
Product Design
held by
trojanrock
Last seen:
Contest Closed
-
Open
-
Choosing Finalist
-
Ended
Description:
We are a manufacturer of Remote Control Toys. We are looking to design a line of flying animals using the base of a current helicopter (attached are pics). We will need the designer to design the outside body in the shape of a Pig, Making a remote control flying pig. The landing gears can be taken off, and the pig will encompass the whole helicopter body. Please submit design 3D design work for a flying Pig.
Wants:
The Pig will be made out of a light plastic material, surrounding the whole helicopter. It will need to be aesthetically pleasing (since most pigs are not naturally good looking), preferably a baby pig. The selected job will be submitted to Shapeways.com for rapid 3D prototyping, so it will need to be in the following format:
DAE, OBJ, STL, X3D, X3DB, X3DV, or WRL
Software:
- AutoCAD
Additional Information
<p>Attached are pics of the base of the helicopter:<br /><br />The measurements for the helicopter is as follows:<br /><br />8 inches (length) from the tip of the nose of the helicopter to the tail<br />2 inches (height) from the bottom of the landing gears to the top of the frame of the helicopter (below the blades)<br />1 inch (width) from the bottom of the helicopter)<br /><br />We want to design the body that covers the whole frame of the helicopter in the shape of a pig. Here are some examples of concepts: <br />http://supercuter.com/wp-content/uploads/2011/06/Baby-pigs.jpg<br />http://rlv.zcache.com/cute_pigs_poster-re001fc8862e541739f6ccdea390f7069_2ukh_400.jpg<br />http://3.bp.blogspot.com/-4fDIuumbpKQ/TazgGxndrBI/AAAAAAAAAIU/QHSewdK7ePY/s320/452038_370.jpg<br />http://25.media.tumblr.com/tumblr_mem9alf7I31rk8kuko1_500.jpg</p>
Payment PendingEntries
#1 pig body for helicopter
by josefdesign
Download Files
Discussion
can i do it in pro-e software
Hello Ricardo,
Yes the picture attached is the actual structure of the helicopter. We are looking to use that base for the pig body.
Yes the picture attached is the actual structure of the helicopter. We are looking to use that base for the pig body.
Hello
The pictures attached are similar to the structer of your helicopter?
Do not have a 2d drawing of all?? The final result would be better, more rigorously.
Thank you
The pictures attached are similar to the structer of your helicopter?
Do not have a 2d drawing of all?? The final result would be better, more rigorously.
Thank you
Sure
Podria diseñar en solidworks y pasarlo a autocad ??
ok great thank you
Yes the helicopter dimensions from the nose to tail is about 8 inches, length from landing gear to top of helicopter frame below the lower blade is about 3 inches, and width is about 2 inches
did you have dimensions ?
Similar Contests on Cad Crowd
Control-box with display, fitting on a DIN rail
This is about a first product draft, which shall later be turned into a production ready design.
I need an enclosure for a custom made electronic part. The rough form-factor should be similar to a navigation system (see attached files) with a display in front and parallel enclosure boundaries, slightly rounded edges.
The display is 4.3 inches wide (see technical details attached) and should be included in the rendering. The enclosure should be 4 cm deep.
As a bonus, the display shows attached bar diagram.
At the back, there should be the possibility for a DIN rail mount, top hat rail EN 50022 – 35 × 7.5
but also for direct wall mount using screws or mounting to a bar with cable ties.
At the front left side of the enclosure, I need a C14 inlet to add a power cable and a Schuko socket: https://en.wikipedia.org/wiki/Schuko or CEE 7/3 socket. See attached figure of the design.
The material should be dark grey with a bit reflective surface. Please add our logo to the upper left corner of the front, below the display. If it fits optically, it could glow a bit in green.
Electrical roller door
Design an electrical roller door using neoprene or similar material for door.
Roller at top.
Design a next generation, WiFi controlled sprinkler unit
We are building a WiFi enabled irrigation unit and need a prototype 3D design that we will print.
Here is our company www.h2lo.co
I have included these photos just to show what the slot on the bottom will look like for the consumer to attach wires to the sprinkler relay.
http://rayshobby.net/wordpress/wp-content/uploads/2013/03/IMG_2424-300x200.jpg
http://rayshobby.net/wordpress/wp-content/uploads/2013/03/IMG_2425-300x200.jpg
http://rayshobby.net/wordpress/wp-content/uploads/2013/03/IMG_2426-300x200.jpg
This design will encase a PCB board with a relay.
quadcopter UAV design contest
I need a unique, rugged quadcopter UAV design,analysis and all necessary fabrication details for production in large quantities.The quadcopter should have a high endurance similar to the Microdrones Md4-1000
LINK:
(http://www.microdrones.com/products/md4-1000/md4-1000-key-information.php#what)
The quadcopter should be modular in nature like the Aeryon Scout
LINK:
Scout(http://ww1.prweb.com/prfiles/2010/09/01/3259734/MG1969.JPG)
NEEDS:
good aesthetic design,analysis along with all production details,
modular nature,
Materials used,
Sourcing details,
Bill of materials(BOM)
4-to-Score Giant
We are an e-commerce company selling on Amazon, eBay, Walmart and our e-commerce website. Our target audience is Children.
We want to design a 4-to-Score Giant like this url https://www.amazon.com/s?k=4-to-Score+Giant&ref=nb_sb_noss.
And now we don't have any good idea yet.
Praveen Raj.V