shop mock up

in 3D Modeling Design held by gibo0211
Contest Closed
  • Open
  • Choosing Finalist
  • Ended
Description:
HI i need few slides on a mockup for a shop front i'm opening.

I need to have 3 main area, On the front counter, bit of space on the left, a hot food display with the GN 1/3 total 6, followed by a hot grill plate around 65/60 followed by cool display for sald ingredient around 9 1/3 gn, so total around 1.1. mtr.

Front top a glass 30 cm high with no top see the attache pictures.


I have attached photo of the shop today,

We need to modify the shop name from Grill and go to "italian street food store, i attache the brand for porpoise.

a drawing with the actual measures of the shop.

On the back i would remove the top price lists and would put this on the left side leaving the top free.

REnedring photo need to be modified with new name and similar counter
Wants:
I need a mock up front of the shop with the correct name on top. i attache the brand file with name "Italian street food store"
i need a drawing showing from different angle and prospective the front shop counter.
total would be two front photo and two drawings.

the order in the counter should be:
Left to right
1) a first part with no appliance on top around 1 mt long, we will display pizza base and Piadina base.
2) hot counter around 80 cm long with 6 1/3 gn no top, this will display different food (chicken, sosages, vegetarian )
3) grill top around 60 cm for 60 cm with space for an hot plate on the left 30X60 on top of this we need to have a small island hoods coming down (stain still and contemporary look)
4) refrigerated buit in part, 1.1 mtr, no top.
5) last bit would be one cashier (ipad) on the left we need to have a movable part of the counter to allow people to pass, around 80 cm.
in front of the cashier we can have a small glass display for fresh croissant ad muffin.
in front of the food display we need to have a glass at list high 30 cm. from the beginning to the end of the refrigerated part.
Colour need to be pretty neutral i would use dark wenge and white.
I need a format file that can reopen in pdf and in any basic architectural software.
I have attache some file of the actual shop and the way the rendering need to look like. I have attached the measures and the appliance i need to install (GGM gastro).

The two histogram file are similar shop to give you a visual on what i need to achieve.
Software:
  1. AutoCAD
Additional Information
The contest has been closed and no winner has been selected.

the only application was incomplete just one picute presented and not front and to pies of the counter. The picute was different from the one i have asked to modify.

To late now to reopen

Entries

= Buyer's Rating
#1 pic 01 by viz_rado

Discussion

gibo0211

Buyer

Wed, 18 Nov 2015 13:43:31 +0000
Hi contest closed and no winner

The only one participating presented only on photo amendment and was not copleted. Cad drawing front and to view missing.

The picture was completely wrong and anywhere near the one i have asked to modify.

Not sure why he has even tried to compete.

Regards

gibo0211

Buyer

Fri, 06 Nov 2015 07:42:02 +0000
hi this is the max i can offer

Tks
Fri, 06 Nov 2015 04:13:11 +0000
2 rendering pics and 1 plan drawing sir will soon on your way.
please reconsider the prize..
it takes time to build the modeling.

gibo0211

Buyer

Thu, 05 Nov 2015 08:16:53 +0000
hi two pictures and 1 drawings from top is ok
tks
Thu, 05 Nov 2015 06:16:39 +0000
maybe simple but time consuming
I agree with Viz
Thu, 05 Nov 2015 04:00:26 +0000
Hi Gibo0211,
viz is right, we would love to do the drawing too, but I have to make clear of your request, you want =
* 2 photo rendering as seen on
1446643568PIADA_Italian_Street_Food___piadaitalianstreetfood______Instagram_photos_and_videos.pdf
* and 2 drawing as in autoCAD drawing of the shop which is = plan and elevation

is that correct?

gibo0211

Buyer

Wed, 04 Nov 2015 16:34:57 +0000
hi i have increased uo to 130 usd, the Job is quite simple and i think is well paid.

Thanks

viz_rado

Designer

Wed, 04 Nov 2015 15:40:42 +0000
Hi ,We can do your task. With best quality. This current job have a lot of details and will take time. But the price is too low. And if you change prepaid amount, we can start work on it. Thank you.

Similar Contests on Cad Crowd

Chocolate Melangeur
I need a stone mill grinder powered by an electric motor. There will be two granite stones weighing circa 10 kg each that will spin on top a granite base, which weighs 15 kg. The base will be at the bottom of a stainless steel pan, which will also contain the 2 stones inside it. The pan will spin by the action of an electric engine/reductor, as its base will be locked on top a metal spinning disc connected to the engine/reductor shaft. The two stones will spin in opposite directions by the action of the spinning base. The stones need to apply a force on the base in order for them to fine ground cocoa bits. In order to that, a system of coils needs to be built so that a force can be applied on each stone. The stones and coil system will have to be easily detachable from the pan, as well as, the pan itself from the disc that holds it, so that chocolate can poured in another recipient.
iPhone/Android Accessory Design Enhancement
This consumer product is an accessory that provides enhanced usability to mobile phones and tablets. The latest design of our "Band" is two parts: 1. Round Base that attaches to the back of the phone (made from a low-friction polymer like polyethylene) 2. A "band" that overlaps with the Round Base (1) and rotates/spins around it. (made from polyethylene over-molded with rubber to provide elasticity to the top band part) The rubber part of the band elongates so that an individual's finger can be placed underneath the band and above the base. The elasticity part is important so it can accommodate different finger sizes. The product allows users to hold the phone more securely. Our current challenge is the design of the "Band" (2). This is where we need the help. As shown in the attached STL file for the Band, there are two circles on either side of the flap that holds the finger down. These circle were put there to provide some added elasticity to the rubber piece. While it does functionally work well, the current design does not look durable or very elegant. We'd like to rethink the band design to make it look incredibly user-friendly, allowing the band to stretch upright to accommodate different finger sizes, while being functionally superior to the current design. Designer will need to provide STL files for my prototyping company to be able to work with.
Industrial Design of a Hand Pulse Detector
We are looking for a industrial design (outlook) of a hand pulse detector. This device will consist of the following. 1) Two metal plates on the device that will come in contact with hand when grip on it. This will form a closed circuit between the plates and thereby detect the electrical pulse from the hand (refer to attached for the existing device). Ideally the area of each contact surface of the metal plate should be more than 2000 square mm. 2) A micro USB port for charging the battery. 3) Power Indicator 4) ON/OFF switch. Internal design of the device is not necessary but must cater enough room to house the below 1) 1500 square mm X 1mm (thickness) PCB 2) 750 square mm X 4mm(thickness) battery. The design shall be in 3D CAD.
ecig design
we need a ecig design, now all ecigs design are boring, all MOD looks the same, ego style all looks the same.we need a unique one,
Unicycle
Hi all, thanks for checking out my contest! I am involved with a company that is looking to receive some entries for a "prototype" electric unicycle. If you aren't familiar let me give you a brief background. Remember the hoverboards last xmas?? The electric unicycle works on essentially the same principle (upside down pendulum theory) to achieve self balancing capability. The current offerings on the market just don't cut it, the plastics are basically thrown together around the requirements of a build, rather than incorporating the necessary components into the design for a smooth finish. I would like the final product to be somewhat futuristic/prototypish looking, maybe a bit sporty. You can get a feeling for whats out there by doing a google search for "electric unicycle". Integral to the design there are 3 requirements. 1.) Obviously the plastic fairing will need to have a cavity for the wheel, but in addition, it will need to subtly include a space for lipo batteries, (doesnt have to be in any particular shape however), and also must include spot for a pcb control board. Both of these items arent excessively large, the PCB is about 4X3 inches and the batteries are about 5X5X1 (but can be reconfigured). 2.) I would also like to incorporate into my design a headlight, and a tail light if possible, but most concerned with head light. Would also like to leave the option open to include small bluetooth speakers, however these would not take very much space at all. 3.) Finally, this design will need to have a retractable handle for balance when getting on/off.