Sustainable TOP CAP packaging for glass containersBlind

This project is for a small WiFi router plastic injection mold that needs to look like a "shield". The PCB (circuit board) is: 2.5 inches in length 1.5 inches in width .5 (half an inch) at its highest point We have included three screenshots of the current injection mold which needs to be redesign. These are JUST for reference to see what the current plastic mold looks like: current-injection-mold-1.jpg current-injection-mold-2.jpg current-injection-mold-3.jpg We have also included a screenshot of the PCB (circuit board) titled: pcb-1.jpg Please note that on that pcb-1.jpg screenshot there are two antennas or wires with green rectangles. Those will be "stuffed" into the mold and have no requirements as far as plastic pieces that need to house or hold them. We will just be pushing them into the hollow area of the mold between the PCB and plastic. What we are trying to do is change our current mold into a plastic shield. Our request is to have a plastic "shield" designed that can house the PCB. This may require the design of the shield to be thicker in height to properly hold the PCB. What we are looking for is AutoCAD design comps of what the new injection mold could look like as a shield, using the very basic dimensions we have outlined above. In regards to the design, we have attached a PDF titled: concept-shield-spec-sheet.pdf This is a VERY basic spec sheet and "concept" design of a shield that we created in house. You do not need to make the design look exactly like this. This spec sheet is just "ideas" we had for a design that would look like a shield and fit the PCB. Designers have full creative freedom to come up with some designs that fit the PCB. We have attached four screenshots of shield designs we like from a company called Vmoda: http://v-moda.com/over-ear-shields/ On that link, the designer can find MANY more ideas on shields V-moda's website all of which we like. Please note that V-moda is just an example of shield designs we like. We know they are a headphone company and have nothing to do with us other than we like their designs. The screenshots are titled: shield-ideas-1.jpg shield-ideas-2.jpg shield-ideas-3.jpg shield-ideas-4.jpg We LOVE these designs and think they could easily work with our PCB which would be underneath the shield. Designers have creative freedom when it comes to the texture on top of the shield, color and most everything else. If the designer so desires, we would even be open to adding additional "non-plastic" elements to the shield design such as "chrome inlays" or "metal edging" etc. This is not a requirement. We just want everyone to know that they can add other materials to the design if they think it will really make the product standout. We do also ask that the designer incorporates our logo into the design of the shield. Our logo is attached in both PSD and PNG format and titled: abox.png abox.psd If there are any questions, please don't hesitate write us. Thanks!

We are coming up with new sensors that we would be installing in gym equipment. We want it to look innovative – that with just one look of our sensors, our brand will be recognized. Besides having an innovative design, we need a wifi logo – or any design showing that the sensor works via wifi/online, and our logo, GYMetrix, should be part of the sensors’ design. We have also attached the holes needed for the sensor to work (colored blue and green on the attached design of our current sensors). The holes have to be in place and can’t be moved. They should be carefully integrated in the design – which is the big part of the challenge. Think out of the box! *Always refer to the files attached for reference. We have added more information regarding the design we need: Color: If possible, the bottom part of the sensor is a different color from the top. So that we can differentiate from the top and bottom part. We have attached an ideal bottom part background we have in mind. Surface: - Bottom surface have to be flat where the blue holes indicated should be. - Top Surface can be anything. Use your imagination! (Like the beacon image attached). - We need one side to be flat. We need this to put stickers for inventory purposes. - One side needs to have the green hole. - The rest, you can use your creativity! Size: Current size of our sensors is 7.3cm x 3.4cm x 2.8cm. Don’t be limited with the current dimensions, you can make it slightly bigger to accommodate your new design. However, make sure the placement of the holes needed should still be in place. Holes: The blue holes indicated in the diagram, is part of the bottom part. Please see attached image “sensor design-holes needed” and other files for reference. The purpose of the 2 holes is where we can (1) turn the sensor on or off and (2) where the light indicator will be. Total number of holes: 3 File types needed: - STEP (.stp) - SolidWorks (.sldprt) - ProE (.prt) - Parasolid (.x_t and .x_b) - ACIS (.sat) - AutoCAD (.dwg, 3D Only) - Autodesk Inventor (.ipt)

We are looking for sleek or a very sexy casing for Home automation device that can add beauty to your house along with making your day to day life easy. We want out of the box thinking, not just any enclosure. The logo will be Maestro, the designer can create it with no limitation for your imaginations. Attached is a pdf file with full requirements and description.

We need a design/file ready for prototype printing and injection molding Product is placed in swimming pool skimmer or pump basket and is in constant water flow. We need a container to hold the copper/silver cilinder to give it a more MARKETABLE LOOK. Plastic container/packaging for blueray xl 4-in-1 Mineral Clarifier. check cilinder in bluerayxl.com. I will need 3 columns with a square plastic netting/strainer (about 3.5 x 5 mm). to let water thru but not debris. Top and bottom i'm attaching strainer sample. use drawing as a guide but keep yellow and blue cylinder sizes intact, container can change slightly in design and measurements.cilinder

We are an internet company from Serbia and the market leader in classifieds portals. We would like to 3D print our logo (we already have a 3D printer - LulzBot TAZ Mini), to be used as a gift for our clients and other marketing purposes. We need the creative solution for a 3D model of our logo. Here are the details: - our logo represents a running man with an "@" instead of a head. We have the logo in 2D, and it should be converted to 3D - we want to have some moving parts on the 3D model (hands, legs, head - we're open to suggestions based on what is possible) - the model should be no more than 10cm in height - we need a .stl file for printing