Hire the best freelance Pipe Stress Analysis expert designers for your company

I am a registered mechanical engineer in the Philippines and earned the fourth place out of 3,841 national licensure examinees. I have 7 years of working experience as a piping engineer and is mainly... Read more

I am a registered mechanical engineer in the Philippines and earned the fourth place out of 3,841 national licensure examinees. I have 7 years of working experience as a piping engineer and is mainly involved in 3D modelling of power plants and chemical plants.

I have 12 years of extensive experience in Piping (Stress & Layout) worked with Aker, Keppel shipyard and other large multinational companies in the offshore and Oil & Gas sectors. I have been activel... Read more

I have 12 years of extensive experience in Piping (Stress & Layout) worked with Aker, Keppel shipyard and other large multinational companies in the offshore and Oil & Gas sectors. I have been actively involved in the Stress analysis of FPSO, FNLG, and LNG carriers (Cryogenic lines). I have a B.Tech degree in Mechanical Engineering from a reputed college in India. Currently I offer the total range of Pipe Stress Analysis (Static & Dynamic) of offshore projects like FPSO, FLNG, FSRU, FSU and LNG carrier and Onshore projects like refineries and power plants. Brief Scope of Services Offered is described below: Stress Analysis ❖ Static and Dynamic analysis of Onshore and Offshore projects. • Static Analysis: Expertise in stress analysis of piping connected to static equipment such as Heat Exchangers, Vessels, Columns, Drums, Reactors, Heaters, Air Fin Fan coolers and tanks Expertise in stress analysis piping connected to rotary equipment such as Pumps (hot and cold) ,Compressors and Turbines. • Dynamic Analysis: ​​ Expertise in dynamic analysis using Caesar II 1. Modal analysis (vibration) 2. Time history analysis (surge, water hammer) 3. Response Spectrum analysis (earthquake) 4. Harmonic analysis. ❖ Identification of critical and non-critical lines and in preparation of stress design basis. ❖ Expertise in basic stress concepts, failure theories and fatigue failure concepts. ❖ Expertise in using judiciously all pipe supports like shoes, saddle, guides, line stops, springs, struts, expansion joints, clamps, U-bolts, adjustable supports etc. ❖ Expertise in calculating static equivalent for occasional case like, seismic, wind and psv. ❖ Expertise in structural sway, two phase flow and slug flow analysis. ❖ Expertise in analysis of jacketed piping (weld check, thickness requirement, buckling check, spacers) for SRU plant. ❖ Competent in analysis of FRP piping (BS 7159). Their Difference from Metallic piping, parameters differences like physical properties, allowable etc. ❖ Familiar with all relevant and applicable design codes like: ASME B31.3 (process piping), ASME B31.1 (power piping), B31.4 (fuel gas piping) B31.8 (gas transmission and distribution, ASME SECTION VIII DIVISION 1 and 2., BS 7159 (FRP), PD5500, DNV ❖ Expertise in using Caesar II. Software Available: 1. CAESARII 6.1 version 2. Auto-Cad 2012

Worked with CAD Softwares like Solidworks , Fusion 360 , Creo. Learning Ansys Currently pursuing Bachelors in Aerospace Engineering Projects : Flying car (Solidworks) : Powertrain Department Aerospik... Read more

Worked with CAD Softwares like Solidworks , Fusion 360 , Creo. Learning Ansys Currently pursuing Bachelors in Aerospace Engineering Projects : Flying car (Solidworks) : Powertrain Department Aerospike Nozzle (Fusion 360)

Highly skilled and experienced Piping Engineer and Pipe Stress Analyst with a strong background in the Oil and Gas industry. Offering expertise in piping design, stress analysis, and project managemen... Read more

Highly skilled and experienced Piping Engineer and Pipe Stress Analyst with a strong background in the Oil and Gas industry. Offering expertise in piping design, stress analysis, and project management. Seeking a challenging role in a reputable organization where I can utilize my skills to contribute to the success of engineering projects.

I am a graduate Mechanical Engineer, pro-active & multi-skilled professional extending rich corporate experience of 7 years in Mechanical & Structural Designs,Pipeline Engineering, Asset integrity & C... Read more

I am a graduate Mechanical Engineer, pro-active & multi-skilled professional extending rich corporate experience of 7 years in Mechanical & Structural Designs,Pipeline Engineering, Asset integrity & Condition Monitoring ,Risk-Based Inspection, Non-Destructive Examination & Evaluation, Corrosion Engineering in oil/gas, Petrochemical, and power/process industries.

A dynamic and committed professional with 16 years of experience in FEED and EPC of piping in various Oil & Gas industries, Process plants, Power plants and FGD. • Piping Stress analysis (Static and D... Read more

A dynamic and committed professional with 16 years of experience in FEED and EPC of piping in various Oil & Gas industries, Process plants, Power plants and FGD. • Piping Stress analysis (Static and Dynamic module) • Vibration assessment and mitigation for piping • Support and Hanger engineering / Modular support. • PDS / PDMS modeling

B.Tech in Mechanical Engineering with 2+ years experience in using Computational Aided Engineering (CAE) techniques for solving various engineering problems as mentioned below: HVAC pipe Stress ana... Read more

B.Tech in Mechanical Engineering with 2+ years experience in using Computational Aided Engineering (CAE) techniques for solving various engineering problems as mentioned below: HVAC pipe Stress analysis Support design for pipelines to withstand Thermal & Seismic loads Surge analysis of HVAC pipes HVAC system optimization for making Greener Building Pulsation & Mechanical Analysis of Pipeline (As per API 618, and API 674 standards) Seismic design of components inside a building Solve complex engineering challenges using mathematical modeling and numerical simulations

I have Thirteen years of experience piping tendering, engineering and construction positions, during which I’ve become an expert in Aveva PDMS, Autodesk Plant 3D, Bentley OpenPlantV8i, and Caepipe sof... Read more

I have Thirteen years of experience piping tendering, engineering and construction positions, during which I’ve become an expert in Aveva PDMS, Autodesk Plant 3D, Bentley OpenPlantV8i, and Caepipe software and Power Plant Mechanical process and Layout. My professional experience includes Tendering, engineering and construction different types of power plants and Oil & Gas plants, and mastering all of the tools involved in the development of different piping systems from the calculation of piping wall thickness to issuing the isometric and spool drawings. The following are my most relevant skills and qualifications: - Modeling of process piping systems using Aveva E3D, and Autodesk Plant 3D - Piping stress analysis and support selection using CAESAR II, and Caepipe - Preparing flow calculation, pressure drop calculation pipe wall thickness, pump selection and tank sizing using Pipe Flow Expert - Tender estimation and technical preparation - Experienced in using international regulations, codes, and standards used in the piping field (API, ASME, ANSI, ASTM, NFPA, AWWA …etc.)

Hi Dear Greetings!! Briefly, I am Ashish Shrivastava independent engineering consultant with 16+ years of experience in pipe stress analysis . I have done wide range of stress analysis in different s... Read more

Hi Dear Greetings!! Briefly, I am Ashish Shrivastava independent engineering consultant with 16+ years of experience in pipe stress analysis . I have done wide range of stress analysis in different sectors like Offshore/onshore, FPSO, Marine, LNG/LPG, Petrochemical. I have a team of freelancers to execute the turnkey projects I only take turnkey projects /remote jobs for pipe stress analysis . I am working on one P78-FPSO Project currently My client list has MNCs names like along with long list of startups and small companies. Petrofac, Seatrium, Quest -Global, KBR, Technip energies, RINA-SPA Thanks & Regards Ashish Shrivastava ▒▒▒▒▒▒▒▒▒▒▒▒▒

Highly creative and upbeat Piping Engineer with 3 years experience in EPC (Engineering Procurement Construction ) companies specialized in oil and gas industries, producing 3D Plant Model and drawing... Read more

Highly creative and upbeat Piping Engineer with 3 years experience in EPC (Engineering Procurement Construction ) companies specialized in oil and gas industries, producing 3D Plant Model and drawing using P&ID's, and providing Stress Analysis according to project specifications. skils: • Preparing 3D models and 2D drawings using CADWorx Plant. • Revieving 3D models using Autodesk Navisworks Review software. • Developing piping isometric drawings. • Producing vessel drawigns using CADWorx Equipment, AutoCad. • Checking piping isometrics per P&ID and specifications. • Creating piping specifications-database using CadWorx specification editor. • Pipe stress analysis using software Caesar II. • Preparing the Stress Critical Line list.

I am a Mechanical Engineer. I have experience of pipe stress analysis on CAESAR-II & Structural Analysis on STAAD Pro. I have designed / performed stress analysis of Steam turbine piping, Methantor... Read more

I am a Mechanical Engineer. I have experience of pipe stress analysis on CAESAR-II & Structural Analysis on STAAD Pro. I have designed / performed stress analysis of Steam turbine piping, Methantor Feed Effluent Heat exchanger piping, Synthesis Compressor piping. I have performed various structural analysis of Pipe Racks, Maintenance / Operating platforms, Storage Sheds, Maintenance sheds, etc

Mechanical Engineering Calculations, Solid works, AutoCAD, 2D to 3D modelling, FEA using ANSYS or equivalent, Pipe Stress analysis, API 650 Tank design, ASME VIII Pressure vessel design and calculatio... Read more

Mechanical Engineering Calculations, Solid works, AutoCAD, 2D to 3D modelling, FEA using ANSYS or equivalent, Pipe Stress analysis, API 650 Tank design, ASME VIII Pressure vessel design and calculations, Equipment calculations to API, ASME, CSA standards, Engineering Authentication.

Highly motivated, highly skilled Physics graduate with 5+ years in Piping Design/ Plant layout & Pipe Stress Analysis. Currently working in the Oil & Gas Industry, both on-shore & off-shore, greenfiel... Read more

Highly motivated, highly skilled Physics graduate with 5+ years in Piping Design/ Plant layout & Pipe Stress Analysis. Currently working in the Oil & Gas Industry, both on-shore & off-shore, greenfield & brownfield projects. I also have experience in the pharmaceutical, mining, and building services industries.

I have over 10 years experience in the design of Oil and Gas industry. There is experience in large project organizations (STG Engineering) . Developing piping drawings, isometric drawings, material t... Read more

I have over 10 years experience in the design of Oil and Gas industry. There is experience in large project organizations (STG Engineering) . Developing piping drawings, isometric drawings, material take-off and stress analysis calculations of pipelines. Work with suppliers of equipment. Supervision of construction sites. Last project was carried out for the company TOTAL (Khatyaga EP-2 ) Professional skills in the work with the programs: AutoCAD, CADWorx Plant 3D, intergraph smart 3D (PDS), AutoPipe, Intergraph CAESAR II - Pipe Stress Analysis, Navisworks

Pipe stress analysis and design engineer with more than eight years of office and field experience in power plant projects (gas and steam turbines, boiler plants), process piping (blast furnace, direc... Read more

Pipe stress analysis and design engineer with more than eight years of office and field experience in power plant projects (gas and steam turbines, boiler plants), process piping (blast furnace, direct reduction plants, slurry transportation, cryogenic piping, etc.) and oil & gas projects (refineries, oil fields). Developed competences in most important piping codes (including ASME B31.1, ASME B31.3, EN-13480, etc.), and acquired proficiency in all aspects of static and dynamic pipe stress analyses (seismic, PSV transients, water hammer, harmonic vibrations, high-frequency vibrations, etc.) including generating critical line list, preliminary route studies and equipment arrangements, building load cases to satisfy code requirements, support design and analysis and fatigue assessments. In-depth knowledge of piping layout design using 3D software. In addition to pipe stress analysis and piping design, which is the primary field of expertise, during the work at the University of Belgrade (as PhD candidate), developed skills in pressure vessel analysis (ASME VIII-1, ASME VIII-2 and EN-13445), process equipment sizing, process design and optimization, heat and mass transfer calculations, fluid flow calculations (steady state and transient, including interaction with the stress analysis), CFD calculations, programming as well as advanced measurement and research techniques which has all proven extremely valuable in the practice. First author and co-author of several engineering and scientific research papers.

Engineering Calculations and Design and Pipe Stress Analysis are primary services offered by MECHANNOVA. Our focus is to provide expert engineering services, maintaining the quality, practical and ti... Read more

Engineering Calculations and Design and Pipe Stress Analysis are primary services offered by MECHANNOVA. Our focus is to provide expert engineering services, maintaining the quality, practical and timely work. From a blank page all the way to complete engineering packages with technical documentation we help companies to build products that are more reliable and more profitable. To find out more about the services we offer, please visit relevant sections of our website. We utilize our engineering skills and experience, technologies and methodologies to provide best engineering solutions in the following industries: Oil&Gas, Petro-chemical, Power generation, Process, Automotive, Manufacturing and Mining industry.

I am a postgraduate in mechanical engineering with 14+ years of strong experience in Piping stress analysis. I have a varied experience in the Oil n Gas sector, Fertilizers, Power, Refinery, and many... Read more

I am a postgraduate in mechanical engineering with 14+ years of strong experience in Piping stress analysis. I have a varied experience in the Oil n Gas sector, Fertilizers, Power, Refinery, and many more. I have dealt with metallic & non-metallic piping. Till now I have been associated with more than 5 national and international clients to carry out their piping stress analysis work successfully. I can help you with - Selection of critical lines from process diagrams (P&IDs) - Discussion with clients - Stress analysis of piping systems using isometrics/layout drawings with Caesar II software - Preparation of stress analysis reports which will be a document in which you can get the following but not restricted to 1. Stress analysis summary & basis 2. P&ID mark up 3. Line list of specified lines 4. Caesar II plot 5. Stress isometric markup with support type arrangement 6. Caesar input report 7. Stress summary 8. Restraint summary 9. Displacement summary 10. Flange leakage summary (if required) 11. Nozzle check sheet (if required) 12. Vendor documents 13. Any additional doc if required If you are looking for quality piping stress-related work, I am the person you can rely on. Tanay

More than 10 years experience of designing of piping systems in 3D. Autocad/ Cadworx, PDMS. More than 4 years experience as Pipe stress engineer in CAESAR II. Projects: 2020 – Expro s.r.o. – Static... Read more

More than 10 years experience of designing of piping systems in 3D. Autocad/ Cadworx, PDMS. More than 4 years experience as Pipe stress engineer in CAESAR II. Projects: 2020 – Expro s.r.o. – Static analysis of steam piping – Reconstruction of steam RCHS 2020 – Intech s.r.o. – Static and dynamic analysis of OVZ – Slovnaft a.s., unit 28 2020 – Intech s.r.o. – Static and dynamic analysis of OVZ – Slovnaft a.s., unit 25,45,44 and 54 2019 - OVZ - increasing reliability of OVZ pipeline - documentation for construction_mechanical part, LPE, static and dynamic analysis of pipeline - Slovnaft, a.s. 2019 - AVD6 - desalters replacement - documentation for construction_mechanical part, static analysis of pipelines - Slovnaft, a.s. 2018/19 - AAG - production capacity increase, replacement of duplicator pipelines - documentation for construction_mechanical part, static analysis of pipelines Slovnaft, a.s. 2018 - SWAATS CW filtration - documentation for construction_mechanical part - Slovnaft, a.s. 2018 - Diesel storage tank - documentation for construction_mechanical part - SAM - SHIPBUILDING AND MACHINERY, a.s. 2018 - RHC - replacement of air filters - documentation for construction_mechanical part - Slovnaft, a.s. 2018 - PYO - new storage tanks - static analysis of pipelines - Slovnaft, a.s. 2018 - NRN - new storage tank - static analysis of pipelines - Slovnaft, a.s. 2018 - AD5 - replacement of pump P7B - documentation for construction_mechanical part, static analysis of pipelines, as built doc. - Slovnaft, a.s. 2017/18 - SWAATS - static analysis of pipe systems - Stercorat Hungary Kft. 2017/18 - SWAATS - documentation for construction, as built doc. _mechanical part - Stercorat Hungary Kft. 2017 - HRP5 - replacement of exchangers pipelines - static analysis of pipe systems 2016 - Replacement of Waste Heat Boiler - documentation for construction_mechanical part - Slovnaft, a.s. 2016 - TBA - flooding protection - documentation for construction_mechanical part - Slovnaft, a.s. 2016 - Flowmeter replacement for Sulfenax - documentation for construction_mechanical part - Duslo, a.s. 2016 - Increasing reliability of PU SAR_ESP filter - documentation for construction_mechanical part - Slovnaft, a.s. 2015 - LDPE4 - AIR DOSING - documentation for construction_mechanical part - Slovnaft, a.s. 2011/15 - Power plant Mochovce - Slovenské elektrárne, a.s.

Amr has 10 years of experience in Design career reflecting pioneering experience and career progression through working in different multinational firms and industries; Oil & Gas and Electro-Mechanica... Read more

Amr has 10 years of experience in Design career reflecting pioneering experience and career progression through working in different multinational firms and industries; Oil & Gas and Electro-Mechanical. My current specialty involves piping engineering (Stress analysis), Code Calculations; and well acquainted with Pipeline Calculations (Hydraulic analysis, Surge Analysis, Pipe Wall thicknesses for internal and external pressure; and branch Connection) as per Referenced ASME Standards. I have a wide exposure to different multinational engineering firm’s environments and standards through participation in part time and full time contracts projects. Core Competencies • Well acquainted with ASME Codes (B31.1, B31.3, B31.4, B31.8, SEC. VIII DIV. 1) Calculations • Preparation of technical specifications and design calculations • Preparing Critical Line Lists • Static and dynamic stress analysis of piping systems (Sustained loads, Expansion loads &Occasional load) Using CAESAR II • Specializing in pipe stress analysis and advising design team on arrangement and support requirement to work within code stress requirements • Pipe support hardware selection & details drawings. • Nozzle flexibility Check • Equipment Nozzles Calculation as per (NEMA SM23, API 610, API 617, API 661 and API 650) • Flanges(Raised & Flat Face, Reversed, Clamped hub) calculations • Isometric Stress Sketches and Civil info Sheets • Proper design of firefighting pipes supports and bracing as per NFPA 2010 chapter 9. • Buried Piping (ASCE, ALLA, PENG, AWWA, NEN 3650). Highlights ASME (B31.1, B31.3, B31.4, B31.8, Sec. Viii Div1); Autocad Plant 3D; AFT Fathom Impulse; Autopipe; Bentley Hammer; Bentley Water Gems; Caesar II; CADWORX; Fluid Networks Computation; Hangers And Springs Selection; Navis Work; Pipe Flo; Pipe Supporting; PRG 2011 (Nozzle Pro, Fe-Pipe, Fe-Bend, Fe-Sif); Revit Mep; Smart Plant 3D; Static & Dynamic Stress Analysis; Surge Analysis; Wall Thickness Calculations; PDMS

Summary biography 14+ years of experience in Development of Detailed and Design engineering for Oil & Gas, Chemical, Petrochemical & Pharmaceutical Industries as Piping Stress & Support Engineer. Core... Read more

Summary biography 14+ years of experience in Development of Detailed and Design engineering for Oil & Gas, Chemical, Petrochemical & Pharmaceutical Industries as Piping Stress & Support Engineer. Core Skill Set ❖ Perform stress analysis for various systems such as: Fired Heater to Reactor piping, Air cooler piping, Pumps piping, large storage tank piping, Cooling Tower piping, Non-metallic piping, PSV piping, Low temperature cryogenic and LNG piping and Jacketed piping’s. ❖ Perform Dynamic analysis (Water Hammer/ Slug Flow – Spectrum) for Surge effects. ❖ Perform stress analysis for Underground & Aboveground pipeline’s (Metallic & Non-Metallic piping). ❖ Perform stress analysis in brown field scopes like Re-Rating study and Cold spring recommendations. ❖ Perform vibration study AIV (Acoustic induced) / FIV (Flow induced) as per EI guideline. ❖ Perform FEA (Using Nozzle Pro) for evaluation of stresses at nozzles, for determining user calculated SIFs, Strength check for welded pipe attachments (like Shoe, Saddle, Lugs, etc,). ❖ Experienced in selection of Expansion joints (Metallic & Non-metallic), springs/struts/Snubbers/Cold supports and their data sheet preparations, MRE, MRO, TBA & Vendor document review. ❖ Able to review customer technical requirements and incorporate in project related pipe stress specifications. ❖ Well conversant with codes & standards like ASME (B31.3,31.4,31.8), API, ISO 14692, ExxonMobil Standards (GP, GII, DP), SHELL DEP & Kuwait Oil Corporation (KOC) Standard’s. ❖ Experienced in resolve site queries of construction team. Proficient in Software • Caesar II - Stress Analysis tool • PRG FEA 2018 – Finite Element Analysis tools • Auto Cad – Drafting tool • SPR & NAVIS – Review tools • MS office tools

I have 10 years of professional experience as a plant design engineer in chemical process industry. During my carrier I have involved more than 10 chemical facility construction projects as a project... Read more

I have 10 years of professional experience as a plant design engineer in chemical process industry. During my carrier I have involved more than 10 chemical facility construction projects as a project engineer. These projects enabled me to gain experience in these areas: -Mechanical Design of Industrial Plants (Chemical, oil & gas, power, food, pharmaceutical, cosmetics) -Preparing PFD P&ID Drawings -3D Pipeline Design (ASME B31.1, ASME B31.3) -Pipe Stress Analysis (ASME B31.1, ASME B31.3, Metal, FRP and GRP piping) -Static Equipment/Process Equipment Design (chemical reactors, mixing tanks, heat exchangers, etc.) -Pressure Vessel Design (ASME Section VIII, EN 13445, AD 2000 - AD Merkblätter, PD 5500, CODAP) -Storage Tank Design (Oil & Gas, solvent, acid, underground and aboveground) (API 620, API 650, API 653, EN 12285-1, EN 12285-2) I want to combine my experience and my ability in design to provide the highest quality service for my clients.